Reply With Quotei dont know much about line-x but i dont thing rhino lining is gonna stick to well to plastic. why are you interested in doing just the flares? i could be wrong about it sticking but i was just always under the impression it was meant for metal.
Line-s or Rhino Line Fender Flares
Hey guys, has anyone had their fender flares done with either Line-X or Rhino? Or know of anyone who has had it done? I am really considering getting it done but want to here from fellow Mil Jeepers before I do. My supervisor is having his '97 painted with Line-X so I am curious to see how it turns out. Any information would be greatly appreciated.
i dont know much about line-x but i dont thing rhino lining is gonna stick to well to plastic. why are you interested in doing just the flares? i could be wrong about it sticking but i was just always under the impression it was meant for metal.
2004 Rubi, Poison Spyder Bumper with Trail Stinger. Warn M8000 winch, Rock Krawler X-factor long arm 4 inch lift, 35x12.50x15 BFG KM2s on Procomp 8 inch steelies, Tom Woods Driveshaft, Poison Syder Full Roll Cage, Tuff Designs rear bumper/Tire carrier, MetalCloak Arched Tube Fenders with 6 Inch Flares, Flowmaster Hushpower Muffler, Vanco Big Disk Brake upgrade, Line-X'd tub and cage.
I have seen decent pics of people who have done it and needless to say it looks good...plus i dont want to spend a ton on bushwackers...and as most jeepers know, the originals fade after time...i have done paint and it just ends up chipping off....
just did this Monday with liner extreeme
97TJ bra liner.JPG
yeah, i plan on solving that problem by getting tube fenders. haha. i have used the duplicolor bumper paint that is made for plastic and it holds up pretty well. no chipping.Originally Posted by millcat72
2004 Rubi, Poison Spyder Bumper with Trail Stinger. Warn M8000 winch, Rock Krawler X-factor long arm 4 inch lift, 35x12.50x15 BFG KM2s on Procomp 8 inch steelies, Tom Woods Driveshaft, Poison Syder Full Roll Cage, Tuff Designs rear bumper/Tire carrier, MetalCloak Arched Tube Fenders with 6 Inch Flares, Flowmaster Hushpower Muffler, Vanco Big Disk Brake upgrade, Line-X'd tub and cage.
i used this a couple of years ago with good results, it just takes time and you should mask the the painted fenders off with tape.
http://www.mothers.com/02_products/06108.html
i plan on doing it to my plastic fenders again, but i think i should pull them off and use the mothers power ball to do it. i just need to get off my lazy a$$...i have to fix my front axle and trans leaks first.
Did you do this yourself? If so, where did you buy the product?
All you need is a compressor that can maintain 60psi or more for spraying. Yea we've been doing truck beds on the side, did my whole tub in about 3hours counting prep. Takes about 3-4hours to prep and spray a long bed truck.
http://www.sprayonbedliners.info/ tell them man cave liners sent you.
I like the way Line-X looks. Has a smoother finish almost like the grain on some stock fender flares on the JK for example. Did it to a truck bed with the Line-X and came out real good. Rhino is gonna look rougher and less even unless you have a good sprayer.
Posting Permissions
Get the MJ Supporter Membership
for a little less than $0.06 a day and
get more space, 2 MJ Stickers and no banners ads. [Check
it out] |
Bookmarks